position pin
英 [pəˈzɪʃn pɪn]
美 [pəˈzɪʃn pɪn]
定位销
双语例句
- Position the door restraint in bracket with the holes aligned and insert the retaining pin.
用孔对齐方式将车门防护移至托架中并且插上固定销。 - Position the pointer over a round handle and drag to rotate. Place a pivot pin into the pivot point.
将指针放至旋转控点上，拖动即可旋转把大头针扎在旋转点上。 - When the counterbalance position moves vertically, the bearing pin is penetrated through a corresponding round hole of the slide way to adjust the height of the platform.
当配重位置发生垂直移动时，通过把承重销轴穿入滑道上对应的圆孔中，实现平台的高度调整。 - Determine the position of the striker pin in relation to the B-pillar according to the impression made at the factory and note it down.
按照工厂制作的压痕确定拉锤相对b柱的位置并记下来。 - Position striker pin and align according to markings.
放置撞销并将其对准标记。 - Determine the position of the striker pin in relation to the B-pillar according to the impression made at the factory and mark this on the striker pin.
根据出厂时的压痕决定锁闩销相对于b柱的位置并在锁闩销上标记。 - Check the position of the dowel pin.
检查定位销的位置。 - Pay attention to the position of the guide pin.
注意导销的位置。 - The utility model discloses a position detection and indication device of a crane pin mechanism.
本实用新型公开了一种起重机插销机构位置检测指示装置。 - The door part Has2 stubs, keeping it in position during mounting of the pin.
门上页片有2个短柱体，用于门铰轴心安装时的定位。 - The fixed position of rubber washer, the punching of outer and center flash, the link-motion of punch pin and the clearance were all analyzed and designed.
对橡胶垫定位、外边冲裁、中心孔冲裁、冲头的联动驱动及冲裁间隙进行了全面分析及设计。 - The results show that the switch operates more steadily at trigger mode than at self-breakdown mode and its operating voltage range is related to such factors as the position of the trigger pin and gas pressure.
研究结果表明开关在自击穿工作下的工作稳定性远小于触发工作时，开关工作范围与触发针位置和气压等因素有关； - The Photoelectric position sensitiva device ( PSD) with a novel PIN structure is mainly used in the auto-focusing system of miniature cameras, the operating principle and the distance-measuring method of the PSD devices are presented.
采用新颍的PIN结构研制的光电位置传感器，主要用于小型相机的自动对焦系统。 - Before the crankshaft pin is punched into its position, the pin and the front and rear crank journals must be washed with the washing petrol blended with 1& 2% of lubricants.
在压入曲轴销前应当用掺有1%～2%润滑油的洗涤汽油将曲柄销和前后曲柄颊清洗干净并吹干。润滑油不能掺得过多，多了会影响组装后的紧配合程度。 - Determine the Position of Steel Bearing Cover at Three Parallel Pin in Supporting Plate
支承板三平行销轴钢套定位方法及实践 - By a specific instance of multi-working position progressive die design for this part, critical process design points are analyzed, and the working principle of grounding pin die is stated in detail.
通过此零件多工位级进模设计的具体案例，分析工艺设计要点，详细阐述接地插脚模具的工作原理。 - Analysis shows that the heavily doping position can influence absorption loss, heat dissipation, extinction ratio ( ER) and speed of the device.
详细分析了pin结的重掺杂区位置对器件的吸收损耗、散热、消光比、速度等的影响。